| Prefix | Suffix | Definition |
| . | . | ROLLER BRG |
| . | . | |
| . | -JFT | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1000 MG/MM |
| . | 02 | REED BEARING W/O.D. CODED TO 0.0001 INCH INCREMENTS |
| . | 03 | REED BEARING W/O.D. CODED TO 0.00005 INCH INCREMENTS |
| . | 20 | REED BEARING W/BORE CODED TO 0.0001 INCH INCREMENTS |
| . | 21 | REED LUBE COBEHN INC., PRECISION INSTRUMENT OIL/MIL-L-6085 |
| . | 22 | REED BEARING W/BORE O.D. CODED TO 0.0001 INCH INCREMENTS |
| . | 22 | REED LUBE ANDERSON OIL CO, WINDSOR LUBE L-245X/MIL-L-6085 |
| . | 23 | REED LUBE CODE 4264 AEROSHELL FLUID I12/MIL-L-6085A2/SKF EA |
| . | 24 | REED LUBE E.F. HOUGHTON CO. COSMOLUBRIC 270/MIL-L-6085 |
| . | 25 | REED LUBE STANDARD OIL OF N.J. UNIVIS P-38/MIL-L-6985- A2/SKF DA |
| . | 26 | REED LUBE ECLIPSE PIONEER P-10/MIL-L-6085-A2/SKF EB |
| . | 27 | REED LUBE ANDEROL L-401-D/MIL-L-6085-A2/SKF EC |
| . | 28 | REED LUBE BRAY 885/MIL-L-6085-A2/SKF DH |
| . | 2GS | SKF REMOVABLE MOLDED NITRILE SEAL ON BOTH SIDES |
| . | 2GSNR | SKF SAME AS -2GS, EXCEPT WITH SNAP-RING |
| . | 2GSP | SKF REMOVABLE MOLDED POLYACRYLIC SEAL ON BOTH SIDES |
| . | 2GSV | SKF REMOVABLE MOLDED FLUOROCARBON SEAL ON BOTH SIDES |
| . | 2RS | SKF SEAL OF PLATE AND SYNTHETIC RUBBER ON BOTH SIDES |
| . | 2RS2 | VITON RUBBER SEALS FOR HIGH TEMPERATURE APPLICATIONS |
| . | 2SS | REED TWO ARMALON SEALS |
| . | 2SS | SKF BACK UP PLATE SEAL ON BOTH SIDES |
| . | 2Z | REED TWO STAINLESS STEEL REMOVABLE SHIELDS |
| . | 2Z | SKF SHIELD ON BOTH SIDES/EX 6203-2Z |
| . | 30 | REED BEARING K/BORE CODED TO 0.00005 INCH INCREMENTS |
| . | 31 | REED LUBE SHELL OIL, CODE 4254 AREO SHELL FL I3/MIL-L-7870 |
| . | 32 | REED LUBE TEXAS 1692 LOW TEMP OIL/MIL-L-7870-A/SKF DD/ |
| . | 33 | REED BEARING W/BORE O.D. CODED TO 0.00005 INCH INCREMENTS |
| . | 33 | REED LUBE STD OIL OF N.J., ESSO AVIATION INSTRU OIL/MIL-L-7870 |
| . | 34 | REED LUBE WINDSOR L-1018/MIL-L-7870-A/SKF DF |
| . | 35 | REED LUBE LEHICRH CHEMICAL PROD., L-407/MIL-L-7870 |
| . | 36 | REED LUBE GULF OIL CO., GULPHITE OIL 6/MIL-L-7870 |
| . | 41 | REED LUBE ESSO RUST BAN 334/SKF FA/ |
| . | 42 | REED LUBE ANDERSON OIL CO, WINDSOR RUST PREV L1384/MIL-L-644 |
| . | 43 | REED LUBE TEXAS CO., TEXACO PRESERVATIVE OIL, SPEC/MIL-L-644 |
| . | 44 | REED LUBE STD OIL OF N.J. , PRESERVATIVE OIL 1193/MIL-L-644 |
| . | 45 | REED LUBE SHELL OIL CO., CODE LG-1-21 SHELL PRESERV/MIL-L-644 |
| . | 46 | REED LUBE E. F. HOUGHTON CO., COSMOLINE 1044/MIL-L-644 |
| . | 51 | REED LUBE VERSILUBE F-50/SKF ED |
| . | 52 | REED LUBE DOW CORNING CORP., DC 200 FLUID/3.0 CS |
| . | 53 | REED LUBE DC-200-20/SKF EF |
| . | 54 | REED LUBE DC-200-30/SKF EF |
| . | 55 | REED LUBE DC-200-350/SKF EG |
| . | 56 | REED LUBE DC-510-20/SKF EG |
| . | 57 | REED LUBE DC-510-50/SKF EJ |
| . | 58 | REED LUBE DC-510-100/SKF EK |
| . | 59 | REED LUBE DC-510-500/SKF EL |
| . | 60 | REED LUBE VERSILUBE F-44/SKF EM |
| . | 65 | REED LUBE TERESSTIC V-78/SKF DG |
| . | 71 | REED LUBE STANDARD OIL OF N.J. BEACON M-325/SKF LB |
| . | 72 | REED LUBE TEXAS CO., TEXACO 1959 UNITEMP GREASE/MIL-G-32 78 / |
| . | 73 | REED LUBE SHELL OIL, CODE 5081 AERO SHELL GREASE LL/MIL-G-3278 |
| . | 74 | REED LUBE E.F. HOUGHTON CO., COSMOILINE 505 GREASE/MIL-G-32 78 |
| . | 75 | REED LUBE LEHIGH CHEM. PROD., ANDEROL L-793 GREASE/MIL-G-32 78 |
| . | 81 | REED LUBE TEXAS 1999 HI TEMP/MIL-G-3545-B/SKF HE |
| . | 82 | REED LUBE SHELL OIL, CODE 5076 AERO SHELL GREASE 5A/MIL-L-3545 |
| . | 83 | REED LUBE SINCLAIR REF. CO., SINCLAIR'HI TEMP GREASE /MIL-L-3545 |
| . | 85 | REED LUBE TEXAS 1996 UNITEMP 500/SKF HD |
| . | 86 | REED LUBE AMER. OIL CO. SUPER MIL ASU-M-100/SKF SC/ |
| . | 87 | REED LUBE DOW CORNING CORP. , DC 33 GREASE/MI55 LIGHT |
| . | 88 | REED LUBE DOW CORNING CORP. , DC 55 GREASE |
| . | 89 | REED LUBE GENERAL ELECTRIC, VERSILUBE G-300 SILICON GREASE |
| . | 90 | REED LUBE G-300 GE VERSILUBE/SKF SF |
| . | 91 | REED LUBE TEXACO CO., REGAL STARFAH MIL-L-7711 GREASE |
| . | 92 | REED LUBE SHELL OIL CO., ETR GRADE 21176A GREASE |
| . | 93 | REED LUBE TEXAS #948-1888 LO TEM/SKF CA |
| . | 94 | REED LUBE GENERAL ELECTRIC CO., JF50 VERSILUBE SILICONE OIL |
| . | 95 | REED LUBE SHELL ETR-B/SKF JB |
| . | 96 | REED LUBE SHELL ETR-D/SKF JC |
| . | 97 | REED LUBE SHELL AEROSHELL I15/MIL-G-25013-C1/SKF JA |
| . | A | REED 0.0000 RADIAL PLAY |
| . | A | SKF BEARING W/ADAPTER FOR AMERICAN SHAFT STANDARD/EX 1606-A |
| . | A | SKF COMPLETE PARCO-LUBRIZE OR SULITE COATING |
| . | A | SKF CONTACT ANGLE 30 DEGREES/EX 7205-A |
| . | A | SKF INTERNAL DESIGN CHANGED/EX 31308-A |
| . | A | TYSON DIMENSIONAL VARIATION FORM BASIC CONE OR CUP |
| . | AB | TYSON DIMENSIONAL VARIATION FROM BASIC FLANGED CUP |
| . | AC | TYSON DIMENSIONAL VARIATION FROM STANDARD CUP |
| . | AS | TYSON DIMENSIONAL VARIATION FORM BASIC CONE OR CUP |
| . | AX | TYSON DIMENSIONAL VARIATION FROM BASIC CONE OR CUP |
| . | B | REED 0.0001 RADIAL PLAY |
| . | B | SKF CONTACT ANGLE 40 DEGREES/EX 7208-B |
| . | B | SKF INTERNAL DESIGN CHANGED/EX 227850-B |
| . | B | TYSON BRASS CAGE CONE |
| . | B | TYSON FLANGED CUP |
| . | BA | SKF LUBE QUAKER CHEM. CO. FERROCOTE OIL S366-K-1 |
| . | BA | SKF HIGH-CAPACITY, 40-DEGREES CONTACT ?.NGLE BALL BRG/EX 7219-BA |
| . | BB | SKF LUBE QUAKER CHEMICAL CO. FERROCOTE OIL #346 |
| . | BC | SKF LUBE SHELL ENSIS OIL £30/MIL-L-21260 |
| . | BD | REED RADIAL PLAY, CATALOG DESIGNATION FOR TIGHT |
| . | BD | SKF LUBE TEXAS PRES. OIL I30/MIL-L-21260 |
| . | BE | SKF LUBE SOCONY MOBIL DTE 797 |
| . | BF | SKF LUBE QUAKER CHEMICAL CO. TMF-5815 |
| . | BG | SKF LUBE MOBILE KOTE $501 |
| . | BJ | SKF LUBE E. F. HOUGHTON CO. COSMOLINE 993/MIL-C-22235 -A |
| . | BW | TYSON SLOTTED FLANGED CUP |
| . | C | REED 0.0002 RADIAL PLAY |
| . | C | SKF CONTACT ANGLE 15 DEGREES/SER 7000 7200 THRU 7208-C |
| . | C | SKF CONTACT ANGLE 20 DEGREES/SER 7200 FORM 7209-CUP |
| . | C | SKF INTERNAL DESIGN CHANGED/EX 23218-C |
| . | C | SKF SPHERICAL ROLLER BRG W/GUIDE RING PRESSED TYPE CAGE |
| . | C | TYSON SPECIAL HIGH-CAPACITY SERIES CONE |
| . | C02 | SKF EXTRA CLOSE INNER RING RUNNING ACCURACY STD INTERNAL CLEAR |
| . | C03 | SKF CLOSE OUTER RING RUNNING ACCURACY STD INTERNAL CLEAR |
| . | C04 | SKF EXTRA CLOSE OUTER RING RUNNING ACCURACY SDT INTERNAL CLEAR |
| . | C06 | SKF COMBINATION OF C02 PLUS C03 |
| . | C07 | SKF COMBINATION OF C01 PLUS C04 |
| . | C2 | SKF RADIAL CLEARANCE LESS THAN NORMAL |
| . | C20 | SKF REDUCED I.D. TOLERANCE APPROACHING NOMINAL DIMENSION |
| . | C3 | SKF RADIAL CLEARANCE GREATER THAN NORMAL |
| . | C30 | SKF REDUCED I.D. TOLERANCE APPROACHING LOW LIMIT |
| . | C4 | SKF RADIAL CLEARANCE GREATER THAN C3 |
| . | C40 | SKF REDUCED O.D. TOLERANCE APPROACHING NOMINAL DIMENSION |
| . | C481 | SKF SUPER PRECISION EQUIV TO RBEC-5 IN BEARINGS/ TAPER BORE/CL FIT |
| . | C4817 | SKF EQUIV TO RBEC-5 TOL, CL FIT, C7 EXTRA-SMOOTH RUNNING |
| . | C5 | SKF RADIAL CLEARANCE GREATER THAN C4 |
| . | C50 | SKF REDUCED O.D. TOLERANCE APPROACHING LOW LIMIT |
| . | C60 | SKF COMBINATION OF C20 PLUS C50 |
| . | C7 | SKF PRECISION ROLLER TOLERANCE |
| . | C70 | SKF COMBINATION OF C20 PLUS C40 |
| . | C77 | SKF SUPER PRECISION ROLLER TOLERANCE |
| . | C78 | SKF SUPER PRECIS, ABEC-5 STD INTERNAL CLEARANCE |
| . | C8 | SKF SPECS ON EXECUTION INSPECTION APPLY/AIRCRAFT/ |
| . | C99177 | SKF SUPER PRECISION, ABEC-7 TOL, CL FIT C77 EXTRA-SMOOTH RUNNING |
| . | C997 | SKF SUPER-PRECISION, ABEC-7 TOLER C7 EXTRA-SMOOTH RUNNING |
| . | CA | SKF LUBE TEXAS 984-1888 LO TEMP |
| . | CA | SKF SPHERICAL ROLLER BEARING W/SEPARATE GUIDE RING INTEGRAL SIDE |
| . | CAM | SKF SPHERICAL ROLLER BEARING W/MACHINED BRONZE INNER PILOTED CAGE |
| . | CAM2 | SKF SPHERICAL ROLLER BEARING W/MACHINED BRONZE ROLLER RIDING CAGE |
| . | CF | REED RADIAL PLAY, CATALOG DESIGNATION FOR STANDARD |
| . | CIO | SKF I.D. O.D. WITHIN LIMITS OF MEAN DIAMETER |
| . | CJ | SKF SPHERICAL ROLLER BEARING PRESSED STEEL INNER PILOTED CAGE |
| . | CK30. | SKF C-TYPE SPHERICAL BEARING WITH L-TO-30 TAPERED BORE/GERMANY |
| . | CL | SKF RADIAL CLEARANCE LESS THAN C2 |
| . | CL3 | SKF BORE, O.D. ECCENTRICITY TOLERANCES EQUIV TO ABEC-3 |
| . | CO1 | SKF CLOSE INNER RING RUNNING ACCURACY STD INTERNAL CLEAR |
| . | COS | SKF CLOSE RUNNING ACCURACY OF BOTH INNER OUTER RINGS |
| . | COS | SKF EXTRA CLOSE RUNNING ACCURACY OF BOTH INNER OUTER RINGS |
| . | CP | TYSON CHROME PLATED CUP OR CONE |
| . | CSV | SKF REMOVABLE MOLDED FLUOROCARBON SEAL |
| . | CY | SKF PRESS BRASS, WINDOW TYPE CAGE, I.R. CENTERED, FOR C SPHERICAL |
| . | D | REED 0.0003 RADIAL PLAY |
| . | D | REED WOUND-SPRING TYPE RETAINER |
| . | D | SKF MATCHED BOXED IN PAIRS FOR DUPLEX MOUNTING |
| . | D | TYSON DOUBLE CONE OR CUP |
| . | D. .B | REED BACK-TO-BACK MOUNT, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . | D. .F | REED FACE-TO-FACE MOUNT, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . | D..T | REED TANDEM MOUNTING, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . | D..U | REED UNIV DUPLEX MOUNT, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . | D9 | SKF DG BALL BEARING W/GROOVES FOR SEALS SHIELDS BUT W/OUT SAME |
| . | DA | SKF LUBE STANDARD OIL OF N.J. UNIVIS P-38/MIL-L-6085-A2/ |
| . | DA | TYSON DIMENSIONAL VARIATION OF BASIC DOUBLE CONE |
| . | DA | TYSON DOUBLE CUP WITH SPHERICAL O.D. |
| . | DB | SKF LUBE ESSO TURBO OIL 4040/MIL-L-7808-E/ |
| . | DB | TYSON FLANGED DOUBLE CUP |
| . | DC | SKF LUBE ESSO AVIATION INSTRUMENT OIL/MIL-L-7870 |
| . | DD | SKF LUBE TEXAS 1692 LOW TEMP OIL/MIL-L-7870 |
| . | DD | TYSON LONG DOUBLE CONE OR DOUBLE CUP |
| . | DE | SKF LUBE WINDSOR LUBE L245X/MIL-L-6085-A2 |
| . | DE | TYSON DIMENSIONAL VARIATION OF BASIC DOUBLE CONE |
| . | DF | SKF LUBE WINDSOR LUBE L-1018/MIL-L-7870A |
| . | DG | SKF LUBE TERESSTIC V-78 |
| . | DH | SKF LUBE BRAY 885/MIL-L-6085-A2 |
| . | DJ | SKF LUBE TERESSTIC V-79 |
| . | DK | SKF LUBE ALASKAN OIL 143 |
| . | DO | SKF SEPARABLE BEARING, NON-INTERCHANGEABLE MAIN COMPONENTS |
| . | DS | TYSON DIMENSIONAL VARIATION OF BASIC DOUBLE CUP |
| . | DT | TYSON DOUBLE CUP, TAPERED O.D. |
| . | DW | TYSON DOUBLE CONE OR CUP WITH KEYWAY OR SLOT |
| . | E | REED 0.0004 RADIAL PLAY |
| . | E3 | REED CORRESPONDS TO ABEC-3 PRECISION |
| . | E4 | SKF SEMI-PRECISION LINEAR MOTION ASSEMBLY |
| . | E5 | REED CORRESPONDS TO ABEC-5 PRECISION |
| . | E7 | REED CORRESPONDS TO ABEC-7 PRECISION |
| . | EA | SKF LUBE CODE 4264 AERO SHELL FLUID J12/MIL-L-6085-A2 |
| . | EA | TYSON CUP SPACER |
| . | EB | SKF LUBE ECLIPSE PIONEER P-10/MIL-L-6085-A2 |
| . | EB | TYSON CUP SPACER |
| . | EC | SKF LUBE ANDEROL L-401-D/MIL-L-6085-A2 |
| . | EC | TYSON CUP SPACER |
| . | ED | SKF LUBE VERSILUBE F-50 |
| . | ED | TYSON CUP SPACER |
| . | ED | TYSON SHORT DOUBLE CUP |
| . | EE | SKF LUBE DC200-20 |
| . | EF | SKF |
| . | EG | SKF |
| . | EH | SKF LUBE DC510-20 |
| . | EJ | SKF LUBE DC510-50 |
| . | EK | SKF LUBE DC510-100 |
| . | EL | SKF LUBE DC510-500 |
| . | EM | SKF LUBE VERSILUBE F-44 |
| . | EN | SKF LUBE 6 TO 8 PARTS XYLENE PLUS 1 PART DC510-50/EJ/ |
| . | EO | SKF EXTRA PRECISION LINEAR MOTION ASSEMBLY |
| . | F | REED 0.0005 RADIAL PLAY |
| . | F | SKF MACHINED STEEL OR MONEL CAGE |
| . | F3 | SKF MACHINED DUCTILE IRON CAGE |
| . | FA | SKF. LUBE ESSO RUST BAN 334 |
| . | FB | SKF LUBE WILSON BROWER THIXOTROPIC OIL 832-20 |
| . | FC | SKF LUBE STANDARD OF N.J. ESSO TURBO 16/MIL-C-8188C |
| . | FC | SKF MACHINED STEEL OR MONEL CAGE CENTERED IN I. R. /PHILA |
| . | FN | REED RADIAL PLAY, CATALOG DESIGNATION FOR LOOSE |
| . | FP | SKF STEEL OR SPECIAL CAST IRON CAGE, SLOT OR BROACH ROLLER CENT |
| . | FPC | SKF SAME AS -FP, EXCEPT INNER RING CENTERED |
| . | FPS | SKF SAME AS -FB, EXCEPT OUTER RING CENTERED |
| . | FR | TYSON FULL ROLL TYPE CONE |
| . | FS | SKF MACHINED STEEL OR MONEL CAGE CENTERED IN O.R./PHILA |
| . | G | REED 0.0006 RADIAL PLAY |
| . | G | SKF FLUSH-GROUND SIDE SURFACES FOR DUPLEX MOUNTING |
| . | G02 | SKF 20 POUNDS PRELOAD |
| . | G05 | SKF 50 POUNDS PRELOAD |
| . | G5 | SKF 500 POUNDS PRELOAD |
| . | GA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 800 MG/MM |
| . | GA | SKF LUBE WILSON BROWER 300-1 |
| . | GB | SKF LUBE WILSON BROWER 300-1-C |
| . | GC | SKF LUBE VALVOLINE OIL CO. TECTYL *437/MIL-C-11796B |
| . | GD | SKF LUBE GULF PETROLATUM EXTRA AMBER |
| . | GL | SKF 100 POUNDS PRELOAD |
| . | GM | REED TORQUE TEST, MODAL TORQUE VALUE OF 800 MG/MM |
| . | GP | REED TORQUE TEST, PEAK TORQUE VALUE OF 800 MG/MM |
| . | GS | SKF REMOVABLE MOLDED NITRILE SEAL ON ONE SIDE |
| . | GSNBR | SKF SAME AS -GSNB , EXCEPT WITH SNAP-RING |
| . | GSNR | SKF SAME AS -GSN, EXCEPT WITH SNAP-RING |
| . | GSP | SKF REMOVABLE MOLDED POLYACRYLIC SEAL |
| . | GSZ | SKF GS-SEAL ON ONE SIDE, Z-PLATE ON THE OTHER SIDE |
| . | H | REED 0.0007 RADIAL PLAY |
| . | H | SKF PRESSED HARDENED STEEL SNAP CAGE |
| . | HA | SKF TORQUE TEST, AVERAGE TORQUE VALUE OF 900 MG/MM |
| . | HA | SKF LUBE STANDARD OF N.J. ANDOK C |
| . | HB | SKF LUBE STANDARD OF N.J. ANDOK-260 |
| . | HC | REED CROWN TYPE STAINLESS STEEL RETAINER |
| . | HC | SKF LUBE STANDARD OF CALIF. KPM AVIATION 42/MIL-G-3545B |
| . | HC | SKF PRESSED STEEL SNAP CAGE, INNER RING CENTERED |
| . | HD | SKF LUBE TEXAS 1996 UNITEMP 500 |
| . | HE | SKF LUBE TEXAS 1999 HI-TEMP/MIL-G-3545-B |
| . | HF | SKF LUBE STANDARD OF CALIF. CHEVRON OHT/MIL-G-18709-A3 |
| . | HG | SKF LUBE STANDARD OF INDIANA RYKON $2 |
| . | HH | SKF LUBE IMPERIAL OIL CO. OF CANADA ESSO MP GREASE 7 |
| . | HJ | SKF LUBE SHELL AERO SHELL I5/MIL-G-3545B |
| . | HK | SKF LUBE N.Y. N.J. S-59 |
| . | HL | SKF LUBE ROYCO 5-N/MIL-G-3545-B/ |
| . | HM | REED TORQUE TEST, MODAL TORQUE VALUE OF 900 MG/MM |
| . | HM | SKF LUBE TEXACO TG 7016 |
| . | HP | REED TORQUE TEST, 'PEAK TORQUE VALUE OF 900 MG/MM |
| . | J | REED 0.0008 RADIAL PLAY |
| . | J | REED RIBBON TYPE STAINLESS STEEL RETAINER |
| . | J | SKF PRESSED UN-HARDENED STEEL CAGE |
| . | JA | =C4054SKF LUBE SHELL AEROSHELL S15/MIL-G-25013-C1 |
| . | JB | SKF LUBE SHELL ETR-B |
| . | JC | SKF LUBE SHELL ETR-D |
| . | JM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1000 MG/MM |
| . | JP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1000 MG/MM |
| . | K | REED 0.0009 RADIAL PLAY |
| . | K | SKF BEARING WITH L-TO-12 TAPERED BORE/EX 1207-K |
| . | K30 | SKF BEARING WITH L-TO-30 TAPERED BORE/EX 24140-CK30 |
| . | KA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1100 MG/MM |
| . | KM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1100 MG/MM |
| . | KP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1100 MG/MM |
| . | L | REED 0.0010 RADIAL PLAY |
| . | L | SKF MACHINED DURAL CAGE |
| . | LA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1200 MG/MM |
| . | LA | SKF LUBE TEXAS LOW-TEMP EP *1346/MIL-G-13827B |
| . | LB | SKF LUBE STD OF N.J. BEACON M-325/MIL-G-32 78 |
| . | LC | SKF LUBE MID CONTINENT OIL CO. MIDCO 287 INSTRUMENT GREASE |
| . | LC | SKF MACHINED DURAL CAGE, CENTERED IN INNER RING |
| . | LD | SKF LUBE SHELL AEROSHELL *7A/MIL-G-3278-AL |
| . | LE | SKF LUBE ANDEROL L-793 |
| . | LF | SKF LUBE ANDEROL L-730/MIL-L-19701 |
| . | LG | SKF LUBE ANDEROL L-795 |
| . | LH | SKF LUBE SHELL AEROSHELL 7/MIL-G-2 3827-A1 |
| . | LJ | SKF LUBE MOBILE GREASE 12 8/MIL-G-23827-A1 |
| . | LK | SKF LUBE ROYCO GREASE T27/MIL-G-23827-AL |
| . | LL | SKF LUBE AMERIC OIL CO. SUPERMIL ASU-72832/MIL-G-23827-A1 |
| . | LM | REED TORQUE TEST, MODAL VALUE OF 1200 MG/MM |
| . | LP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1200 MG/MM |
| . | LP | SKF MACHINED DURAL CAGE W/BROACHED POCKETS |
| . | LPC | SKF MACHINED DURAL CAGE W/BROACHED POCKETS, I.R. CENTERED |
| . | LPS | SKF MACHINED DURAL CAGE W/BROACHED POCKETS, O.R. CENTERED |
| . | LW1 | TYSON CONE WITH ONE SPECIAL KEYWAY |
| . | M | REED 0.0011 RADIAL PLAY |
| . | M | SKF MACHINED BRONZE CAGE |
| . | M2 | SKF SPHERICAL ROLLER BEARING W/ ROLLER-RIDING CAGE AND NO GUIDE-RING |
| . | M2 | SKF TRACTION MTR BEARING W/ SOLID BRASS DRILL CAGE, ROLL-CENTERED |
| . | M5 | SKF SOLID SILIC-IRON BRONZE CAGE/ALL VARIATIONS OF M APPLY |
| . | MA | SKF LUBE MASTER LUBRICANT M-31 |
| . | MB | SKF LUBE N.Y. N.J. W-56/MIL-G-18709-A3 |
| . | MC | SKF LUBE SOCONY VACUUM BRB LIFETIME |
| . | MC | SKF MACHINED BRONZE CAGE CENTERED IN INNER RACE |
| . | MC5 | SKF CAGE-SAME AS MC, EXC SILICONE IRON BRONZE MATERIAL |
| . | MD | SKF LUBE SHELL CYPRINA *3 |
| . | MG | SKF LUBE SHELL ALVANIA B/AAR SPEC. M-917-56 |
| . | MH | SKF LUBE FISKE BROS. LUBRIPLATE 107 |
| . | MJ | SKF LUBE SHELL ALVANIA 13 |
| . | MK | SKF . LUBE SHELL DARINA F2 |
| . | MN | SKF - LUBE SHELL DARINA AX |
| . | MO | SKF LUBE TEX 1909 JOURNL RB GREASE H/AAR SPEC. M-917-63 GRADE B |
| . | MP | SKF MACHINED BRONZE CAGE WITH BROACHED POCKETS |
| . | MPC | SKF CAGE-SAME AS -MP EXCEPT CENTERED IN INNER RACE |
| . | MPC5 | SKF CAGE-SAME AS -MPC, EXCEPT SILICONE IRON BRONZE MATERIAL |
| . | MPS | SKF CAGE-SAME AS -MP EXCEPT CENTERED IN THE OUTER RACE |
| . | MPS5 | SKF CAGE-SAME AS -MPS, EXC SILICON IRON BRONZE MATERIAL |
| . | MR | SKF LUBE TEXACO 2301 RB GREASE/AAR SPEC M-917-63 GRADE A |
| . | MS | SKF LUBE ESSO ARAPEN RB-350/AAR SPEC. M-917-63 GRADE A |
| . | MS | SKF MACHINED BRONZE CAGE CENTERED IN THE OUTER RACE |
| . | MS5 | SKF CAGE-SAME AS -MS, EXCEPT SILICON IRON BRONZE MATERIAL |
| . | MT | SKF LUBE RICHFIELD ROCOLUBE/AAR SPEC M-917-63 GRADE A |
| . | MU | SKF LUBE SHELL ALVANIA C/AAR SPEC M-917-63 GRADE B |
| . | MW | SKF LUBE MOBIL PLEX EP-2/MIL-G-18709-A3 |
| . | MX | SKF LUBE NON-FLUID OIL CO. F-924-AF |
| . | MY | SKF LUBE UNION OIL OF CALIFORNIA UNOBA $1 |
| . | N | REED 0.0012 RADIAL PLAY |
| . | N | SKF GROOVE IN OUTER RACE BUT WITHOUT SNAP-RING/EX 6205-N |
| . | N | TYSON' TYSON SERIES ONLY |
| . | NA | REED TORQUE TEST, AVERAGE VALUE OF 1300 MG/MM |
| . | NA | SKF LUBE SHELL B B/MIL-G-10924B |
| . | NB | SKF. LUBE AEROSHELL F 14/MIL-G-25537-A1 |
| . | NFR | TYSON FULL-ROLL CONE IN TYSON SERIES |
| . | NM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1300 MG/INM |
| . | NP | REED TORQUE TEST, PEAK VALUE OF 1300 MG/MRA |
| . | NR | SKF SNAP RING ON OUTER RING |
| . | NW | TYSON SLOTTED FRONT FACE ON NA-TYPE CONE |
| . | NW2 | TYSON CONE WITH 2 SPECIAL WOODRUFF KEYS |
| . | NW4 | TYSON CONE WITH 1 KEYWAY EXTENDED THROUGH CONE BORE |
| . | Q | SKF QUIET RUNNING BEARING |
| . | QA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1400 MG/MM |
| . | QM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1400 MG/MM |
| . | QP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1400 MG/MM |
| . | RA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1500 MG/MRA |
| . | RA | SKF LUBE DOW CORNING DC-33/LIGHT |
| . | RB | SKF LUBE DOW CORNING DC-44/LIGHT/MIL-L-15719-A3 |
| . | RB | TYSON CUP WITH SNAP RING |
| . | RD | SKF LUBE DOW CORNING DC6 SILICONE |
| . | RL | SKF FOLLOWED BY NON-SIGNIFICANT NOS/SPEC INTERN RAD CLEAR |
| . | RM | REED TORQUE. TEST, MODAL TORQUE VALUE OF 1500 MG/MM |
| . | RP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1500 MG/MM |
| . | RS | SKF SEAL OF PLATE AND SYNTHETIC RUBBER ON ONE SIDE |
| . | RSNBR | SKF SAME AS-RSNB, EXCEPT WITH SNAP-RING |
| . | RSNR | SKF SAME AS-RSN, EXCEPT WITH SNAP-RING |
| . | RSZ | SKF RS-SEAL ON ONE SIDE, Z -PLATE ON THE OTHER SIDE |
| . | S | SKF DIMENSIONAL VARIATION FROM BASIC CONE |
| . | SA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1600 MG/MM |
| . | SA | SKF LUBE KEYSTONE M-89 SILICONE |
| . | SB | SKF LUBE DOW CORNING DC-4 SILICONE |
| . | SC | SKF LUBE AMERICAN OIL CO. SUPERMIL ASU-M-100 |
| . | SD | SKF LUBE AMERICAN OIL CO. SUPERMIL ASU-M-40 |
| . | SE | SKF LUBE DOW CORNING PNEUMATIC GREASE 55-M/MIL-L-4 343 |
| . | SF | SKF LUBE G-300 GE VERSILUBE |
| . | SG | SKF LUBE AMERICAN OIL CO. SUPERMIL M-125 |
| . | SH | SKF LUBE MOBIL GREASE 24 |
| . | SJ | SKF LUBE AMERICAN OIL CO. SUPERMIL ASU-31052/MIL-G-25013D |
| . | SK | SKF LUBE MOBIL TEMP FL |
| . | SM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1600 MG/RAM |
| . | SP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1600 MG/MM |
| . | SS | REED ONE ARMALON SEAL |
| . | SS | SKF BACK-UP PLATE SEAL ON ONE SIDE |
| . | SW | TYSON DIMENSIONAL VARIATION FROM BASIC CONE WITH KEYWAY |
| . | SW | TYSON NA-TYPE CONE WITH SLOTTED FRONT-FACE |
| . | SWE | TYSON NA-CONE, SLOT FRONT-FACE EXTENDED FACE-FACE GROUND FOR SEAL |
| . | T | REED SYNTHETIC SNAP-ON TYPE RETAINER |
| . | T | SKF PHENOLIC CAGE/EX 6305-T |
| . | T | TYSON CUP WITH TAPERED O.D. |
| . | T | TYSON TAPERED BORE ON CONE |
| . | TA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1700 MG/MM |
| . | TA | SKF LUBE STANDARD OF N.J. ANDOK B/MIL-G018709-A3 |
| . | TB | SKF LUBE TEXACO 1982 REGAL STARFAK F3 |
| . | TC | REED SYNTHETIC INNER RING SUPPORTED RETAINER |
| . | TC | SKF LUBE STANDARD OF N.J. ESSO AVIATION GENERAL PURPOSE |
| . | TC | SKF PHENOLIC CAGE, INNER RING CENTERED/EX 6204-TC |
| . | TD | SKF LUBE SOCONY MOBILGREASE AERO GENERAL PURPOSE |
| . | TD | TYSON DOUBLE CONE WITH TAPERED BORE |
| . | TE | SKF LUBE SHELL ALVANIA J2/MIL-G-18709-A3 |
| . | TF | SKF LUBE NEW YORK NEW JERSEY S-58/MIL-G-18709-A3 |
| . | TG | SKF LUBE MASTER LUBRICANT LUBRICO M-24-M/MIL-G-18709-A3 |
| . | TH | SKF LUBE SHELL CYPRINA RA |
| . | TJ | SKF LUBE STANDARD OIL OF N.J. ANDOK BR |
| . | TK | SKF LUBE IMPERIAL OIL CO ./CANADA/ANDOK 280 |
| . | TL | SKF LUBE IMPERIAL OIL CO ./CANADA/ESSO MP GREASE M |
| . | TM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1700 MG/MM |
| . | TM | SKF LUBE TEXAS REGAL AFB #2/MIL-G-7711A |
| . | TN | SKF LUBE KEYSTONE 84-HX LIGHT |
| . | TN | SKF NYLON OR NYLAFIL CAGE/EX 6203-TN |
| . | TNC | SKF NYLON OR NYLAFIL CAGE, INNER RING CENTERED/EC 6205-TNC |
| . | TNS | SKF NYLON OR NYLAFIL CAGE, OUTER RING CENTERED/EX 6205-TNS |
| . | TO | SKF LUBE SHELL ALVANIA EP2 |
| . | TP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1700 MG/MM |
| . | TP | SKF LUBE CHEVRON OIL CO. RPM AVIATION GREASE TL |
| . | TS | REED SYNTHETIC OUTER RING SUPPORTED RETAINER |
| . | TS | SKF PHENOLIC CAGE, OUTER RING CENTERED/EX 6204-TS |
| . | U | SKF ALIGNING WASHER FOR THRUST BALL BEARING/EX 708-U/PHILA |
| . | UA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1800 MG/MM |
| . | UA | SKF LUBE AM. OIL CO. SUPERMIL ASU 06752/MIL-G-27560-A3 |
| . | UB | SKF LUBE CHEVRON OIL CO. BRB-2 |
| . | UC | SKF LUBE SHELL AEROSHELL F 16/MIL-G-25760 |
| . | UD | SKF LUBE MOBIL GREASE S38/MIL-G-81322A |
| . | UE | SKF LUBE CHEVRON OIL CO. SRI 12 |
| . | UM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1800 MG/MM |
| . | UP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1800 MG/MM |
| . | VAA | SKF SPECIAL CHARACTERISTICS IN BASIC SIZE-LETTERS INSIGNIFICANT |
| . | VAB | SKF SPECIAL CHARACTERISTICS IN BASIC SIZE-LETTERS INSIGNIFICANT |
| . | VAC | SKF SPECIAL CHARACTERISTICS IN BASIC SIZE-LETTERS INSIGNIFICANT |
| . | VSA | SKF SPECIAL CHARACTERISTICS IN BEARING SERIES-LETTERS INSIGNIFICANT |
| . | VSB | SKF SPECIAL CHARACTERISTICS IN BEARING SERIES-LETTERS INSIGNIFICANT |
| . | VSC | SKF SPECIAL CHARACTERISTICS IN BEARING SERIES-LETTERS INSIGNIFICANT |
| . | W | REED FULL BALL COMPLEMENT DESIGN -NO RETAINER |
| . | W | TYSON 2 ANG SLOTS DIAMETRICALLY OPPOSITE IN CONE BACK-FACE |
| . | W10 | SKF BEARING WITH DULITED SURFACES |
| . | W100 | REED 1200 NIG/MM MAX STARTING TORQUE, 75 GR. LOAD |
| . | W101 | REED 1000 MG/MM MAX STARTING TORQUE, 75 GR . LOAD |
| . | W102 | REED 5400 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . | W103 | REED 5000 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . | W104 | REED 4600 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . | W105 | REED 4200 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . | W106 | REED 3800 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . | W107 | REED 3400 MG/MM MAX STARTING TORQUE, 400 GR . LOAD |
| . | W108 | SKF NON-STANDARD SHIELD CLEARANCE OF 0.008 TO 0.009 INCH |
| . | W109 | REED EXTREME CORROSION RESISTANCE |
| . | W115 | SKF WLL BEARINGS WITH ADDITION OF W5 FEATURES |
| . | W12 | SKF RACEWAYS AND ROLLING ELEMENTS DULITED. ALL OTHER SURFACES PARCO-LUBRIZED |
| . | W125 | SKF W12 BEARINGS WITH ADDITION OF W5 FEATURES |
| . | W13 | SKF BEARING WITH PARCO-LUBRIZED BORE AND O.D. |
| . | W14 | SKF DULITED RINGS ROLLING ELEMENTS, PARCO-LUBRIZED BORE O.D. |
| . | W15 | SKF ALL SUFACES DULITED, EXCEPT LANDS SUPPORTING CAGE RIDE |
| . | W16 | SKF PARCO-LUBRIZED INNER RING AND O.D. OF OUTER RING |
| . | W17 | SKF DULITED CAPPED BEARING, EXCEPT SHIELD OR SEAL TIN-COATED |
| . | W18 | SKF BEARING W/SPECIFIC DULITED SURFACE OR SURFACES |
| . | W19 | SKF BEARINGS WITH SPECIAL RADIAL LOOSENESS LIMITS |
| . | W2 | SKF BEARING MEETING SPECIAL TORQUE REQUIREMENTS |
| . | W21 | SKF FLUSH GROUND BEARING W/INNER OUTER RINGS OF EQUAL WIDTH/ CLOSE CROSS CORNER TOLERANCES./ |
| . | W215 | SKF W21 BEARINGS WITH ADDITION OF W5 FEATURES |
| . | W216 | SKF W21 BEARINGS WITH ADDITION OF W6 FEATURES |
| . | W22 | SKF SPEC REDUCED O.D. TOLERANCE FOR O.R. -STD TOLER FOR I.R. |
| . | W23 | SKF SPECIAL FEATURES FOR TRACTION MOTOR BEARINGS |
| . | W24 | SKF SPECIAL TOLERANCE FOR SEAL OR SHIELD LOCATION ON CAPPED BEARINGS |
| . | W25 | SKF SPHERICAL ROLLER BEARINGS W/CLOSE OUTER RING WIDTH TOLERANCE |
| . | W26 | SKF SPHERICAL ROLLER BEARINGS W/HOLES DRILLED THROUGH THE INNER RING |
| . | W27 | SKF SY PILLOW BLOCK BEARINGS WITH A SPECIAL COLLAR |
| . | W29 | SKF CYLINDRICAL W/SPECIAL RADIAL LOOSENESS INTERCHANGEABILITY |
| . | W2CX | SKF OIL HOLES IN OUTER 'RING OF SPHERICAL ROLLER BEARING |
| . | W3 | SKF BEARING MARKED TO SHOW MEASURED ACCURACY |
| . | W30 | SKF BEARINGS WITH SPECIFIED PARTS TIN-PLATED |
| . | W31 | SKF SPHER BEARXNGS INSPECTED TO CERTAIN QUALITY CONTROL REQUIREMENT |
| . | W32 | SKF PLATES SEALS INSPECTED TO SPECIAL MINIMUM LOOSENESS |
| . | W33 | SKF SPHERICAL ROLLER BEARING W/OIL HOLES CIRCUMFERENTIAL GROOVE IN O.D. |
| . | W34 | SKF CAGE HAS BEEN 10 PERCENT FLUORESCENT PENETRANT INSPECTED |
| . | W35 | SKF SPDG BEARING W/ REDUCED SIDE RUN-OUT OF INNER RING |
| . | W36 | SKF BEARINGS THAT HAVE BEEN QUALITY AUDITED FOR BORE AND O.D. |
| . | W37 | SKF SPECIAL AIRCRAFT BEARING IDENTIFICATION |
| . | W38 | SKF WRIGHT AERO, QUALITY ASSURANCE |
| . | W39 | SKF ALLISON QUALITY ASSURANCE |
| . | W4 | SKF HI-POINT OF ECCENTRICITY MARKED ON INNER RING OR SLEEVE |
| . | W40 | SKF BEARINGS WITH SILVER PLATED CAGE |
| . | W405 | SKF W40 BEARINGS WITH ADDITION OF W5 FEATURES |
| . | W41 | SKF BEARINGS WITH SILVER AND LEAD PLATED CAGES |
| . | W42 | SKF BEARINGS WITH SILVER AND LEAD-INDIUM PLATED CAGE |
| . | W43 | SKF BEARINGS WITH CHROME PLATED CAGE |
| . | W45 | SKF CADMIUM PLATED LOCKOUTS AND WASHERS |
| . | W5 | SKF CUSTOMERS PART NUMBER MARKED ON BEARING |
| . | W50 | SKF BEARINGS W/DOUBLE STABILIZED HEAT TREATED INNER RACES |
| . | W501 | SKF W19 BEARINGS WITH ADDITION OF W36 FEATURES |
| . | W502 | SKF W22 BEARINGS WITH ADDITION OF W33 FEATURES |
| . | W503 | SKF W4 BEARINGS WITH ADDITION OF W33 FEATURES |
| . | W504 | SKF W55 BEARINGS WITH ADDITION OF W33 FEATURES |
| . | W505 | SKF W51 BEARINGS WITH ADDITION OF W33 FEATURES |
| . | W506 | SKF W31 BEARINGS WITH ADDITION OF W33 FEATURES |
| . | W507 | SKF W4 BEARINGS WITH ADDITION OF W31 FEATURES |
| . | W508 | SKF W4 BEARINGS WITH ADDITION OF W31 FEATURES |
| . | W509 | SKF W26 BEARINGS WITH ADDITION OF W31 AND W33 FEATURES |
| . | W51 | SKF SPECIAL NOISE TEST AND CARTON MARKING |
| . | W510 | SKF W33 BEARINGS WITH ADDITION OF K56 FEATURES |
| . | W512 | SKF W22 BEARINGS WITH ADDITION OF W31 AND W33 FEATURES |
| . | W513 | SKF W33 BEARINGS WITH ADDITION OF W26 FEATURES |
| . | W514 | SKF W26 BEARINGS WITH ADDITION OF W31 FEATURES |
| . | W515 | SKF W4 BEARINGS WITH ADDITION OF W58 FEATURES |
| . | W516 | SKF W10 BEARINGS WITH ADDITION OF W33 FEATURES |
| . | W517 | SKF COMBINATION OF W33 PLUS W61 |
| . | W518 | SKF COMBINATION OF W20 PLUS W26 |
| . | W519 | SKF COMBINATION W81 PLUS W20/USED W/SPECIAL NOS. ONLY/ |
| . | W52 | SKF SINGLE CAP BEARINGS WITH MARKING ON SIDE OPPOSITE CAP |
| . | W521 | SKF COMBINATION OF W5 PLUS W74 |
| . | W522 | SKF COMBINATION OF W81 PLUS W33/USED W/SPECIAL NOS. ONLY/ |
| . | W523 | SKF COMBINATION OF W31 PLUS W76 |
| . | W524 | SKF COMBINATION C02 W507 |
| . | W525 | .SKF COMBINATION W31 W77 |
| . | W526 | SKF COMBINATION W506 W515 |
| . | W527 | SKF COMBINATION W22 W33 W26 |
| . | W53 | SKF BALL BEARINGS MODIFIED AND FLUSH GROUND ON ONE FACE ONLY |
| . | W54 | SKF SPECIAL QUIET RUNNING BEARINGS |
| . | W55 | SKF BEARINGS WITH LOCATING HOLES IN THE OUTER RING |
| . | W56 | SKF LIFTING HOLES IN FACE OF BEARINGS RING |
| . | W57 | SKF GE MOTOR BEARING QUALITY ASSURANCE |
| . | W58 | SKF OUTER RING MARKED TO SHOW HIGH POINT |
| . | W59 | SKF SPECIAL FORD MOTOR CO. QUALITY REQUIREMENTS |
| . | W6 | SKF GEAR SIDE MARKED ON BEARING |
| . | W60 | SKF QUALITY ASSURANCE U.S. NAVY PURCHASE OF G.E. BEARINGS |
| . | W61 | SKF BEARINGS W/3 TAPPED HOLES IN THE FACE OF THE OUTER RING |
| . | W62 | SKF CYL BEARING-SIDE FLANGES W/15-TO-30 MINUTES RELIEF ANGLE |
| . | W63 | SKF MARKING FOR DEVIATION FROM NOMINAL OUTER-DIAMETER SIZE |
| . | W66 | SKF BLIND HOLE IN O.D. OF CYLINDRICAL ROLLER BEARINGS |
| . | W67 | SKF CYLINDRICAL BEARINGS W/OVERSIZE O.D. FOR GREATER HOUSING FIT |
| . | W7 | SKF BEARING BORE DIAMETER INDICATED |
| . | W70 | SKF CYLINDRICAL W/INCREASED OUTER RING AXIAL CLEARANCE |
| . | W71 | SKF SPECIAL MARKING FOR SIKORSKY BEARINGS PURCHASED BY U.S. NAVY |
| . | W72 | SKF CYLINDRICAL BEARING W/ANGLED FLANGE INCREASED AXIAL CLARANCE |
| . | W73 | SKF SPHERICAL ROLLER BEARING WITH ONE COUNTERBORED HOLE IN OUTER RING |
| . | W74 | SKF BALL BEARING, J-CAGE TYPE WITH CONTROLLED CAGE DROP |
| . | W75 | SKF STD CONRAD BALL BEARING W/REPUBLIC ROCKED TUBE HOFORS BALLS |
| . | W76 | SKF FOUR TAPED HOLES IN EACH FACE OF OUTER RING |
| . | W77 | SKF SPHERICAL ROLLER BEARING WITH W33 GROOVE HOLES/HOLES CIBORED PLUGGED/ |
| . | W79 | SKF W33 SPHERICAL ROLLER WITH ONE HOLE COUNTERBORED |
| . | W8 | SKF NO LUBE-HOLE IN O.K. OF BEARING USED IN SY PILLOW BLOCK |
| . | W80 | SKF SPECIAL BEARING-I .R. , O.K. ROLLERS AIR-MELT CARBURIZED GRADE STEEL |
| . | W81 | SKF SPECIAL BEARING/I. R. AIR-MELT CARBURIZED GRADE OF STEEL |
| . | W82 | SKF SPECIAL BEARING/0. R. AIR-MELT CARBURIZED GRADE OF STEEL |
| . | W83 | SKF W81 PLUS W82, PLUS STANDARD THRU HARDENED ROLLERS |
| . | W86 | SKF SPECIAL BEARING/I. R. O.R. STD THRU HARD, ROLLERS CARBURIZED GRADE STEEL |
| . | W90 | SKF . SAME AS W80 , EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . | W91 | SKF SAME AS W81, EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . | W92 | SKF SAME AS W82 , EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . | W93 | SKF SAME AS VJ83, EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . | W96 | SKF SAME AS W86 , EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . | WA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1900 MG/MM |
| . | WA | TYSON SLOTTED CONE-SINGLE ANGULAR SLOT IN BACKFACE |
| . | WB | TYSON TWO SLOTS DIAMETRICALLY OPPOSITE IN BACK-FACE OF CONE |
| . | WD | TYSON SPECIAL SLOTTED CONE |
| . | WE | TYSON SLOTTED CONE- FULL LENGTH SLOT THROUGH BORE |
| . | WHO | REED DENTAL DRILL QUALITY BEARING |
| . | WILL | REED BEARING STABILIZED FOR 900-F OPERATION |
| . | WLL | SKF BEARING WITH PARCO-LUBRIZED SURFACES |
| . | WM | REED TORQUE TEST, MODAL TORQUE VALUE OF 1900 MG/MM |
| . | WP | REED TORQUE TEST, PEAK TORQUE VALUE OF 1900 MG/MM |
| . | X | SKF BOUNDARY DIMENSIONS CHANGED TO CONFORM TO INTERNAT STD |
| . | X | TYSON CONE, WITH KEYWAY |
| . | X | TYSON VARIATION FROM BASIC CUP |
| . | XA | TYSON CONE SPACER |
| . | XB | TYSON CONE SPACER |
| . | XC | TYSON CONE SPACER |
| . | XD | TYSON DOUBLE CONE OR CUP |
| . | XL | TYSON CONE, CUP OR ASSEMBLY SEALED WITH TY-SEAL |
| . | Y | SKF PRESSED BRASS OR BRONZE CAGE/EX 6303-Y |
| . | YA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 2000 MG/IRTM |
| . | YC | SKF PRESSED BRASS OR BRONZE CAGE CENTERED ON INNER RACE |
| . | YP | REED TORQUE TEST, PEAK TORQUE VALUE OF 2000 MG/MM |
| . | Z | REED ONE STAINLESS STEEL REMOVABLE SHIELD |
| . | Z | SKF SHIELD ON ONE SIDE/EX 6203-Z/ |
| . | ZA | REED TORQUE TEST, AVERAGE TORQUE VALUE OF 2100 MG/MM |
| . | ZM | REED TORQUE TEST, MODAL TORQUE VALUE OF 2100 MG/MM |
| . | ZNBR | SKF SHIELD SNAP RING ON SAME SIDE/EX 6206-ZNBR/ |
| . | ZNR | SKF SHIELD SNAP RING ON OPPOSITE SIDES/EX 6206-ZNR |
| . | ZP | REED TORQUE TEST, PEAK TORQUE VALUE OF 2100 MG/MRA |
| A | . | REED DEEP GROOVE NARROW SERIES STRAIGHT O.D., FLUSH RINGS |
| AHA | . | SKF REMOVAL SLEEVE WITH AMERICAN STD THREAD/PHILA |
| AN | . | SKF NUT FOR ADAPTER SLEEVE/PHILA |
| ARM | . | SKF REMOVAL NUT FOR ASK-TYPE SLEEVE/EX ARN-18 |
| ASK | . | SKF REMOVAL SLEEVE/EX ASK-15 |
| B | . | BREMEN LOOSE NEEDLE ROLLER W/SPHERICAL ENDS/STANDARD/EX B142 |
| B | . | REED BEARING MATERIAL-BERYLLIUM COPPER ALLOY |
| B | . | REED DEEP GROOVE, NARROW SERIES, STRAIGHT O.D., EXTENDED INNER RING |
| BB | . | BREMEN DRAWN CUP, OPEN END NEEDLE ROLL BRG/EX BB182212 |
| BB | OH | BREMEN SAME AS BB-, EXC WITH OIL-HOLE/EX BB- 182212-OH |
| BBH | . | BREMEN SAME AS BB- , EXC HEAVY-DUTY/EX BBH-162112 |
| BBH | OH | BREMEN SAME ASJ3BH-, EXC WITH OIL-HOLE/EX BBH-162112-OH |
| BD | . | BREMEN DRAWN CUP, CLOSED END, GREASE RETAINED NEEDLE ROLLER BRG |
| BDH | . | BREMEN DRAWN CUP, CLOSED END NEEDLE ROLL BRG/EX BDH-162116 |
| BDH | OH | BREMEN SAME AS BDH- , EXC WITH OIL-HOLE/EX BDH-162112-OH/ |
| BF | . | BREMEN DRAWN CUP W/OUTWARD TURNED LIP, GREASE RETAINED NEEDLE |
| BFF | F | SKF SPECIAL PILLOW BLOCK FOR BUFFALO FORGE- REPLACES BF-F |
| BN | . | BREMEN DRAWN CUP, RETAINER TYPE, CLOSED END ROLL BRG/BN-121608 |
| BNH | . | BREMEN SAME AS BN-, EXC HEAVY-DUTY/EX BNH-071108 |
| BP | . | BREMEN CAGE NEEDLE ROLLER ASSEMBLY/EX BP7767 |
| BR | . | BREMEN DRAWN CUP, RETAINER TYPE, OPEN END ROLLER BRG/BR-121608 |
| BR | T | BREMEN SAME AS BR- , EXC W/MOLDED NITRILE SEAL ON ONE SIDE |
| BR | TT | BREMEN SAME AS BR- , EXC W/MOLDED NITRILE SEAL ON BOTH SIDE |
| BRH | . | BREMEN SAME AS BR- , EXC HEAVY-DUTY/EX BRH-071108 |
| BT | . | BREMEN NEEDLE ROLLER THRUST BEARIN'G/EX BT-9929-5-46 |
| C | . | REED DEEP GROVE, NARROW SERIES, FLANGED O.D., FLUSH RINGS |
| CR | . | TYSON RIBBED CUP |
| D | . | REED DEEP GROOVE, NARROW SERIES, FLANGED O.D. , EXTENDED INNER RING |
| E | . | REED DEEP GROVE, MEDIUM SERIES, STRAIGHT O.D., FLUSH RINGS |
| ECB | . | SKF SPHERICAL BEARING/AIRMELT CARBURIZED STEEL I.R. ONLY/PHILA |
| ECC | . | SKF SPHERICAL BEARING AIRMELT CARBURIZED STEEL I.R. O.R. ONLY/ PHILA |
| ECD | . | SKF SPHERICAL BEARING, AIRMELT CARBURIZED STEEL, COMPLETE/PHILA |
| EDHP | G | SKF SYHP IN DUCTILE IRON, RE-LUBE, WITH 478-VSB SERIES BEARING |
| EE | . | SKF EXTRA-SMALL, INCH DIMENSION BALL BEARING/EX EE-9 |
| EE | . | TYSON LARGE BORE DOUBLE RIB TYPE CONSTRUCTION CONE |
| EEA | . | SKF SAME AS EE-, EXC REVISED DIMENSIONS/EX EEA2 , EEA2-2Z |
| EEB | . | SKF SAME AS EE-, EXC LARGER WIDTH TO ACCOMODATE SEALING |
| EGA | . | SKF SPHERICAL BEARING/AIRMELT CARBURIZED STEEL, O.R. ONLY/PHILA |
| EH | . | TYSON EXTRA HEAVY SERIES CONE OR CUP |
| EL | . | TYSON EXTRA LIGHT SERIES CONE OR CUP |
| EP | . | SKF SPHERICAL ROLLER BEARING W/PRECISION TOLERANCES/PHILA/ |
| EPCA | . | SKF SAME AS ECA-, EXCEPT WITH PRECISION TOLERANCES |
| EPCB | . | SKF SAME AS ECB-, EXCEPT WITH PRECISION TOLERANCES |
| EPCC | . | SKF SAME AS ECC-, EXCEPT WITH PRECISION TOLERANCES |
| EPCD | . | SKF SAME AS ECD-, EXCEPT WITH PRECISION TOLERANCES |
| EPVA | . | SKF SAME AS EVA-, EXCEPT WITH PRECISION TOLERANCES |
| EPVB | . | SKF SAME AS EVB- , EXCEPT WITH PRECISION TOLERANCES |
| EPVC | . | SKF SAME AS EVC-, EXCEPT WITH PRECISION TOLERANCES |
| EPVD | . | SKF SAME AS EVD-, EXCEPT WITH PRECISION TOLERANCES |
| ER | . | SKF TRIPLE SEAL RING FOR PILLOW BLOCK/EX ER-846 |
| EVA | . | SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, O.R. ONLY/ PHILA |
| EVB | . | SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, I.R. ONLY/ PHILA |
| EVC | . | SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, I.R. O.R. ONLY/PHILA |
| EVD | . | SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, COMPLETE/ PHILA |
| F | . | REED DEEP GROOVE, MEDIUM SERIES, CYLINDRICAL O.D., EXTENDED INNER RING |
| F | . | SKF PRESSED STEEL FLANGE, 3-BOLTS/EX F-40 |
| FD | . | SKF FY IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| FD | C | SKF FALSE TWIST SPINDLE, INTERNAL DES CHANGED/EX FD-630-C |
| FD | G | SKF FY IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| FD | P | SKF FY IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 479 SERIES BEARING |
| FD | PG | SKF FY IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 479 SERIES BEARING |
| FDL | . | SKF FYL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| FDL | G | SKF FYL IN DUCTILE IRON, RE-LUBE, WITH 454-VSB SERIES BEARING |
| FDL | P | SKF FYL IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 454 SERIES BEARING |
| FDL | PG | SKF FYL IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 454-VSB SERIES BEARING |
| FDP | . | SKF FYP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| FDP | G | SKF FYP IN DUCTILE IRON, RE-LUBE, WITH 478-VSB SERIES BEARING |
| FDP | P | SKF FYP IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 478 SERIES BEARING |
| FDP | PG | SKF FYP IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 478-VSB SERIES BEARING |
| FDT | . | SKF FYT IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| FDT | G | SKF FYT IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| FDT | P | SKF FYT IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 479 SERIES BEARING |
| FDT | PG | SKF FYT IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, -479 SERIES BEARING |
| FDTL | . | SKF FYTL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| FDTL | G | SKF FYTL IN DUCTILE IRON, RE-LUBE, WITH 454-VSB SERIES BEARING |
| FDTL | P | SKF FYTL IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 454 SERIES BEARING |
| FDTL | PG | SKF FYTL IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 454- VSB SERIES BEARING |
| FDTP | . | SKF FYTP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| FDTP | G | SKF FYTP IN DUCTILE IRON, RE-LUBE, WITH 478- VSB SERIES BEARING |
| FDTP | P | SKF FYTP IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 478 SERIES BEARING |
| FDTP | PG | SKF FYTP IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 478- VSB SERIES BEARING |
| FDTX | . | SKF FYTX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| FDTX | G | SKF FYTX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| FDTX | P | SKF FYTX IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 477 SERIES BEARING |
| FDTX | PG | SKF FYTX IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 477 SERIES BEARING |
| FDX | . | SKF FYX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| FDX | G | SKF FYX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| FDX | P | SKF FYX IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 477 SERIES BEARING |
| FDX | PG | SKF FYX IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 477 SERIES BEARING |
| FE | . | SKF BOLSTER SPRINGS/EX FE-148/ TEXTILE APPLICATION |
| FL | . | SKF SAME AS FP , EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FP | . | SKF 3-BOLT PRESSED STEEL ROUND FLANGE BEARING/EX FP-102 |
| FP | . | SKF FIXED BOSS TOP ROLLER/EX FP-2/TEXTILE APPLICATION |
| FR | . | SKF BELT GUIDE ROLLER/EX FR-23241/TEXTILE APPLICATION |
| FT | . | SKF PRESSED STEEL FLANGE, 2-BOLTS/EX FT-40/ |
| FTL | . | SKF SAME AS FTP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FTP | . | SKF 2-BOLT PRESSED STEEL ELONGATED FLANGE BEARING/EX FTP102 |
| FY | . | SKF FLANGED HOUSING BEARING W/SET SCREW COLLAR/EX FY-102 |
| FY | X | SKF FLANGED HOUSING BEARING W/ECCENTRIC COLLAR/EX FY-102-X |
| FYL | . | SKF SAME AS FYP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FYP | . | SKF FLANGED HOUSING BEARING W/SET SCREW COLLAR/EX FYP-102 |
| FYR | . | SKF FLANGED ROUND HOUSING SPHERICAL BEARING W/SET SCREW/ EX FYR107 |
| FYR | P | SKF SAME AS FYR- , EXC REVERSE FLANGE MOUNTING/FYR-107-P |
| FYTL | . | SKF SAME AS FYTP EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FYTP | . | SKF TWO BOLTS, CAST IRON FLANGE UNIT WITH 478 SERIES BEARING |
| G | . | REED DEEP GROOVE, MEDIUM SERIES, FLANGED O.D., FLUSH RINGS |
| GL | . | SKF SAME AS GP , EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| GN | A | SKF HI-CAPACITY N-SERIES W/HYATT CORNER RADIUS |
| GNF | A | SKF HI-CAPACITY NF-SERIES W/HYATT CORNER RADIUS |
| GNJ | A | SKF HI-CAPACITY NJ-SERIES W/HYATT CORNER RADIUS |
| GNP | A | SKF HI-CAPACITY NP-SERIES W/HYATT CORNER RADIUS |
| GNU | A | SKF HI-CAPACITY NU-SERIES W/HYATT CORNER RADIUS |
| GNUP | A | SKF HI-CAPACITY NUP-SERIES W/HYATT CORNER RADIUS |
| GP | . | SKF CYL CARTRIDGE W/SPHERED O.D. RUBBER MOUNTING/EX GP-12 |
| H | . | REED DEEP GROOVE, MEDIUM SERIES, FLANGED O.D., EXTENDED INNER RING |
| H | . | TYSON HEAVY SERIES CUP OR CONE |
| HA | . | SKF ADAPTER SLEEVE FOR AMERICAN STANDARD SHAFT/EX HA-2313 |
| HF | . | SKF BOLSTER INSERT/EX HF-4/TEXTILE APPLICATION |
| HH | . | TYSON HEAVY-HEAVY SERIES CUP OR CONE |
| HHC | AB | SKF SIZE OF SER HNC-A WITH WIDTH NON-CONFORMING ISO STDS |
| HHJ | AB | SKF SIZE OF SER HNJ-A WITH WIDTH NON-CONFORMING ISO STDS |
| HM | . | SKF BOLSTER INSERT/EX HM-337/OLD STYLE, REPLACEMENT ONLY |
| HM | . | TYSON HEAVY-MEDIUM SERIES CUP OR CONE |
| HMJ | A | SKF CRB, TWO SNAP-RINGS IN O.R., ONE LIP IN I.R., J-CAGE/HNJ206-A |
| HMVP | . | SKF HYDRAULIC NUT/EX HMVP-76 |
| HNC | A | SKF CRB, TWO SNAP-RINGS IN O.K., TWO LIPS IN I.R., J-CAGE/HNC206A |
| HNC | ABV | SKF SIZE OF SER HNC-AV WITH WIDTH NON-CONFORMING ISO STDS |
| HNC | AV | SKF CRB, TWO SNAP-RINGS IN O.K., TWO LIPS IN I.R., NO CAGE |
| HNU | . | SKF OUTER RING OF SNAP-RING TYPE CYLINDRICAL ROLLER BEARINGS |
| HNU | A | SKF CYLINDRICAL ROLLER BEARINGS TWO SNAP-RINGS IN O.R., STRAIGHT I.R. , J-CAGE/HNU-206-A |
| HUU | J | SKF CAGE OF SNAP-RING TYPE CYLINDRICAL ROLLER BEARINGS |
| HZ | . | SKF BOLSTER BASE UNIT/EX HZ-66/TEXTILE APPLICATION |
| I- | . | SKF AS PER DRAWING I-.../SER OR SPEC/STAMPED CHANGES TO |
| J | . | BREMEN LOOSE NEEDLE ROLLER W/FLAT SHEARED ENDS/EX J-1056 |
| J | . | REED DEEP GROOVE, EXTRA NARROW SERIES, STRAIGHT O.D., FLUSH RINGS |
| J | . | TYSON SIZE EQUIVALENT TO CORRESPONDING IN TIMKEN J-LINE |
| K | . | TYSON SPECIAL HEAVY DOUBLE CUP OR ROLLER ASSEMBLY |
| KNU | AB | SKF SIZE OF SER HNU-A WITH WIDTH NON-CONFORMING ISO STDS |
| L | . | TYSON LIGHT SERIES CUP OR CONE |
| LER | . | SKF TRIPLE SEAL RING FOR PILLOW BLOCK/EX LER-14 |
| LHNC | AB | SKF SAME AS LHNC-A WITH WIDTH NON-CONFORMING TO ISO STDS |
| LHNJ | A | SKF INNER RACE OF HNJ-A/EX LHNJ-206-A |
| LHNJ | AB | SKF SAME AS LHNJ-A WITH WIDTH NON-CONFORMING TO ISO STDS |
| LHNU | A | SKF INNER RACE OF HNU-A/EX LHNU-206-A |
| LHNU | AB | SKF SAME AS LHNU-A WITH WIDTH NON-CONFORMING TO ISO STDS |
| LL | . | TYSON LIGHT-LIGHT SERIES CONE OR CUP |
| LM | . | TYSON LIGHT-MEDIUM SERIES CUP OR CONE |
| LP | . | SKF LOOSE BOSS TOP ROLL/EX LP-512-32/TEXTILE APPLICATION |
| LZ | . | SKF CAPPED-BAR TYPE TOP ROLLER/EX LZ-512/TEXTILE APPLICATION |
| M | . | BREMEN SAME AS B-PREFIX BUT DIFFER HEAT-TREAT O.R. DIMENS DATA |
| M | . | REED ANGULAR CONTACT, NARROW SERIES, FLANGED O.D., FLUSH RINGS |
| M | . | TYSON MEDIUM SERIES CUP OR CONE |
| MB | . | SKF LOCKWASHER/EX MB-18 |
| MBL | . | SKF LOCKWASHER/EX MBL-36 |
| N | . | REED DEEP GROOVE, INCH SERIES, STRAIGHT O.D. FLUSH RINGS |
| N | . | SKF CYLINDRICAL BEARING W/TWO FLANGES IN I.R. NO FLANGES IN O.R. |
| N | . | SKF LOCKNUT/EX N-08/PHILA ONLY |
| NA | . | TYSON NON-ADJUSTABLE CONE/ FACTORY ADJUST/USED W/DOUBLE CUP |
| NF | . | SKF CYLINDRICAL BEARING W/TWO FLANGES IN I.R. ONE FLANGE IN O.R. |
| NH | . | SKF SAME AS N.J.., PLUS STABILIZING RING |
| NJ | . | SKF CYLINDRICAL BEARING W/ONE FLANGE IN I.R. TWO FLANGES IN O.R. |
| NN | . | SKF 2-OR MORE-ROW CYLINDRICAL BEARING/FLANGED INNER, FLANGLESS OUTER |
| NN | K | SKF SAME AS NN-, EXC L-TO-12 TAPER BORE/EX NN-3007-K/ |
| NP | . | SKF CYL BRG, 2-FLANGE INNER, 1-FLANGE OUTER W/PLATE |
| NU | . | SKF CYLINDRICAL BEARING W/NO FLANGES IN I.R. TWO FLANGE IN O.R. |
| NUP | . | SKF CYLINDRICAL BEARING, 2-FLANGE OUTER, 1-FLANGE INNER W/PLATE |
| P | . | REED DEEP GROOVE, INCH SERIES, FLANGED O.D., FLUSH RINGS |
| P | . | SKF LOCK-PLATE FOR LOCKNUT/EX P-76/ |
| P | . | SKF SPHERICAL ROLLER BEARING W/SPLIT O.R. /EX 22320-P/ |
| PK | . | SKF PENDULUM WEIGHTING ARM/EX PK-101/TEXTILE APPLICATION |
| R | . | REED DEEP GROOVE, INCH SERIES, STRAIGHT O.D., EXTENDED INNER RING |
| R | . | SKF SMALL SIZE SINGLE ROW, DEEP-GROOVE BALL BEARING/EX R-9 |
| RGNU-F | . | SKF OUTER RING CAGE ROLLER ASSEMBLY STAVE TYPE G SERIES BEARINGS |
| RHNU | BJ | SKF SAME AS RHNU-J WITH WITH NON-CONFORMING TO ISO STDS |
| RHNU | J | SKF OUTER RING ROLLER ASSY OF HNJ-A AND HNU-A/RHNU206-J |
| RL | . | SKF SAME AS RP , EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| RN | . | SKF CYLINDRICAL ROLLER BEARING, 2-FLANGE INNER, NO OUTER RING/ EX RM-210/ |
| RN | . | SKF REMOVAL NUT FOR SK-SLEEVE/EX RN-12 |
| RNU | . | SKF CYLINDRICAL ROLLER BEARING, 2-FLANGE OUTER, NO INNER RING/ EX RNU-210 |
| RP | . | SKF RUBBER MOUNTED CYLINDRICAL CARTRIDGE UNIT/EX RP-14 |
| S | . | SKF ADAPTER SLEEVE/EX S-15, PART OF SNW -15 |
| SA | . | REED SAME AS A-PREFX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SAF | . | SKF SPLIT PILLOW BLOCK HOUSING W/TRIPLE SEALS/EX SAF-609 |
| SAFS | . | SKF SAF PILLOW BLOCK OF CAST STEEL |
| SB | . | REED SAME AS B-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SC | . | REED SAME AS C-PREFIX, EXC 400-C S/STEEL IN LIEU OF STD 52100 |
| SD | . | REED SAME AS D-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SD | . | SKF SY IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| SD | G | SKF SY IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| SDAF | . | SKF SPLIT PILLOW BLOCK HOUSING W/TRIPLE SEALS/EX SDAF-530 |
| SDAFS | . | SKF SDAF PILLOW BLOCK OF CAST STEEL |
| SDH | . | SKF SYH IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| SDH | G | SKF SYH IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| SDHL | . | SKF SYHL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| SDHL | G | SKF SYHL IN DUCTILE IRON, RE-LUBE, WITH 454-VSB SERIES BEARING |
| SDHP | . | SKF SYHP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| SDHX | . | SKF SYHX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| SDHX | G | SKF SYHX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| SDK | . | SKF SYX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| SDK | G | SKF SYX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| SDL | . | SKF SYL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| SDL | G | SKF SYL IN DUCTILE IRON, RE-LUBE WITH 454-VSB SERIES BEARING |
| SDP | . | SKF SYP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| SDP | G | SKF SYP IN DUCTILE IRON, RE-LUBE, WITH 478-VSB SERIES BEARING |
| SE | . | REED SAME AS E-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SF | . | REED SAME AS F-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SG | . | REED SAME AS G-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SJ | . | REED SAME AS J-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD. 52100 |
| SK | . | SKF REMOVABLE SLEEVE/EX SK-28 |
| SL | . | SKF SAME AS SP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SN | . | REED SAME AS N-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SNP | . | SKF ADAPTER WITH NUT AND LOCKPLATE/EX SNP-3098 |
| SNW | . | SKF ADAPTER WITH NUT AND LOCKWASHER/EX SNW-08 |
| SP | . | REED SAME AS P-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SP | . | SKF PRESSED STEEL PILLOW BLOCK/EX SP-102 |
| SR | . | BREMEN LOOSE NEEDLE ROLLER W/FLAT GROUND ENDS/EX SR-902/ |
| SR | . | REED SAME AS R-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SR | . | SKF SR-23, -24, -25 ARE IDLER PULLEY SPINDLES/TEXTILE APPLICATION/ |
| SR | . | SKF SR-270, -290, -3120 ARE COMPLETE TENSION PULLEYS/TEXTILE APPLICATION/ |
| SR | . | SKF STABILIZING RING FOR PILLOW BLOCK/EX SR-20-17, SR-1610 |
| SR | . | SKF TAPE TENSION PULLEY/EX SR-23/TEXTILE APPLICATION |
| SR | B | SKF SAME AS SR- , EXCEPT PARKERIZED SHELL/EX SR-7-B |
| SR | B | SKF SAME AS SR- , EXCEPT SPECIAL DIMENSIONS/EX SR-23-B |
| SR | E | SKF SAME AS SR-, EXC INTERNAL F LINGER PARKERIZED SHELL |
| SR | H | SKF SAME AS SR-, EXCEPT EXTRA WIDTH/EX SR-290-H |
| SRL | . | SKF SAME AS SRP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SRP | . | SKF PRESSED STEEL PILLOW BLOCK, RUBBER MOUNTED/EX SPR-14 |
| SS | . | REED SAME AS S-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| ST | . | SKF LINEAR MOTION ASSEMBLY, HELD TYPE/EX ST-1232 |
| SW | . | SKF LINEAR 'MOTION ASSY, FLOATING TYPE/EX SW-1232 |
| SY | . | SKF UNIT BALL BEARING PILLOW BLOCK, SET SCREW COLLAR/EX SY-100 |
| SYH | X | SKF SAME AS SY, EXC ECCENTRIC COLLAR HEIGHT/EX SYH- 104-X |
| SYHL | . | SKF SAME AS SYHP EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SYHP | . | SKF SAME AS SYH, EXCEPT WITH 478 BEARING SERIES/EX SYHP-102 |
| SYL | . | SKF SAME AS SYP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SYP | . | SKF SAME AS SY , EXC 478 SER BEARING ECCENTRIC COLLAR/SYP102 |
| SYR | . | SKF SPHERICAL ROLLER BEARING PILLOW BLOCK UNIT/EX SYR-208 |
| TB | . | SKF BALL BEARING TAKE-UP UNIT/EX TB-104 |
| TBL | . | SKF SAME AS TBP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| TBP | . | SKF BALL BEARING TAKE-UP UNIT/EX TBP-104 |
| TBX | . | SKF BALL BEARING TAKE-UP UNIT/EX TBX-104 |
| TM | . | REED TORQUE TEST, MODAL TORQUE VALUE OF 2000 MG/IMN |
| TW | . | BREMEN NEEDLE ROLLER THRUST RACE/EX TW-1220-2 |
| TY | R | SKF TAKE-UP UNIT WITHOUT ADJUSTING FRAINE/EX TY-203-R |
| TY | R-PS | SKF TAKE-UP UNIT WITH ADJUSTING FRAME/EX TY-203-R-PS-12 |
| UL | . | SKF BOTTOM ROLLER BEARING/EX UL-LL-28/TEXTILE APPLICATION |
| VR | . | SKF SEPARATOR ROLLS/EX VR-2/TEXTILE APPLICATION |
| W | . | SKF GREASE SEAL/EX W-2854 |
| W | . | SKF GREASE LOCK WASHER/EX W-08 |
| X | . | TYSON EXPERIMENTAL OR LIMITED PRODUCTION/EX X-68-1/ |
| Y | A | SKF PROPELLER SHAFT BOX/EX Y-5463-A |
| •SH | . | REED SAME AS H-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
